The Fundamentals of Plumbing Knowledge When Installing a Bathtub
The Fundamentals of Plumbing Knowledge When Installing a Bathtub
Blog Article
On this page in the next paragraph you can locate some dependable news in regards to Tools You Need to Install a New Bathtub .
Installing a tub isn't precisely brain surgery, however it does require strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old bathtub with a new one is also a moderately tough project. If the old tub is conveniently obtainable, the job can move easily; if you have to open up a wall surface to eliminate the old tub and place the new bathtub, the task is much harder. In either situation, the project is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub and embeded in the new one. Ensure you have certified yourself for the work as well as are comfortable attempting it. Rather than hiring a service provider to take control of a halfway-completed job, it is better to think about utilizing one prior to you start. Chances are you might require a professional plumber to make tube connections.
This post will certainly assist you install a new bathtub in your restroom if you have actually already acquired a new tub and do not require to change the plan of your previous water supply pipes.
Your devices as well as product checklist should comprise the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water system. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be quite problematic as a result of the restricted accessibility that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. As soon as the supply pipelines have actually been removed, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any old sealing substance.
Before proceeding to fit the new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin making sure that the washers are in location between the tap as well as the sink. Secure the tap in place with the maker provided backnut. As soon as the tap is securely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type must be attached to the tap ends first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Setting up the Tub
Making use of the two wooden boards under its feet, place the tub in the required placement. The wooden boards are helpful in evenly spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the bathtub till the level checks out degree.
To install taps, fit the bottom of the furthest flexible faucet port to the proper supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Activate the water system and examine all joints and also brand-new pipework for leakages and also tighten them if essential. Load the tub as well as likewise inspect the overflow outlet and the normal electrical outlet for leaks.
Ultimately, take care of the bath paneling as described in the manufacturer's user's manual. Tiling as well as securing around the tub must wait until the bathtub has been utilized a minimum of when as this will settle it right into its last setting.
Getting ready for the Setup
Firstly, the supporting framework provided with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the tap features a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to stop pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be suited its last placement.
Tiling Around the Bathtub
In the location where the bath fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to break a stiff seal, causing the water to pass through the wall surface between the bath and also the tiling, resulting in complications with wetness and feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and also installations. They are marketed in tubes and cartridges, and also are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly load the bath tub with water before securing, to enable the movement experienced when the tub is in use. The sealer can break rather early if you do not take into consideration this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily offered on the market. It is suggested to fit the floor tiles making use of waterproof or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that blog posting about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing research the internet. So long as you appreciated our blog entry please do not forget to share it. Thank you so much for your time spent reading it.
Fast and effective, call! Report this page